How To Reconstitute hCG (Step-by-step guide w/Pictures!)

hCG is a peptide which is bought in powdered form. In order to inject this compound, it must be reconstituted through the use of either sterile water or bacteriostatic water. Both are acceptable re-constitutional ingredients, however the use of sterile water will see the hCG degrade at a faster rate than bacteriostatic water.

Preface
Assuming your vial of hCG is vacuum sealed (as many are), when you reconstitutie the hCG, withdraw your sterile water/bacteriostatic water then firmly hold the plunger of the syringe as you insert it through the stopper of the hCG vial. Don't let it suck the water from your pin. Turn the vial at a slight angle and slowly drip water down the side of the vial being sure not to shoot water directly at the powder. Your hCG should melt, if it fizzes up you've possibly just damaged the hormone. Do not shake the hCG, instead lightly swirl it and store it in a fridge and use for upto 30-40 days

Ingredients
1 x hCG Vial
Sterile Water or Bacteriostatic Water
1 x 1ml 29g 1/2" Needle (Insulin Needle)
Alcohol Swabs

Dosages
Working out dosages for hCG is simple.

+) If you have 5,000IU hCG in the vial, and 20ml of sterile/bacteriostatic water, reconstituting this will create 250IU/ml.

+) If you have 5,000IU hCG in the vial, and 10ml of sterile/bacteriostatic water, reconstituting this will create 500IU/ml.

+) If you have 5,000IU hCG in the vial, and 5ml of sterile/bacteriostatic water, reconstituting this will create 1,000IU/ml.

+) If you have 5,000IU hCG in the vial, and 2ml of sterile/bacteriostatic water, reconstituting this will create 2,500IU/ml.

+) If you have 5,000IU hCG in the vial, and 1ml of sterile/bacteriostatic water, reconstituting this will create 5,000IU/ml.

Step 1
Take the cap off the hCG vial, so that it is ready to be swabbed by an alcohol pad.

Step 2
Prepare Insulin Needle (1 x 1ml 29g 1/2" Needle).

Step 3
Use an alcohol swab to wipe the top of the hCG vial.

Step 4
Prepare Sterile Water/Bacteriostatic (Sterile water in this case) ampoule and identify cracking point.

Step 5
Crack ampoule.

Step 6
Withdraw water from the sterile water ampoule.

Step 7
Inject sterile water into the hCG vial, slowly and ensure the water does not come in direct contact with the powder, instead inject so that the water falls onto the side of the vial and hits the glass before it comes into contact with the powder - hCG alongside all peptides are very sensitive compounds.

Be very careful that there is no vacuum from the difference in pressure with the atmosphere and the pressure within the vial. To combat this, inject the amount (ml) into the vial before withdrawing that same amount (ml).

Step 8
Now either store the hCG in the fridge ready for consumption or inject subcutaneously (a step-by-step guide will follow).

Remember to be using your ai while on hcg.. High estro conversions

If you waited until your fourth week to start that would be fine. I had to do some major research on this as well and every time I asked someone I would get some long drawn out answer that didn't make sense to me. But you can do the ratio many different ways. The way eastcoast said would work fine, but your injecting .5cc of hcg. IMHO less is better so what I do is take the 1ml bac water and inject into your hcg, turn slowly like instructed until dissolved. Take that 1ml and inject into an empty sterile vial and then add an additional 1ml of bac water to the vial. You now have 2ml of 5000iu hcg. You are gonna want to inject 250iu twice a week. That on your 100 pin would only be the first 10 which is .1cc Smaller amount but same potency. This is just how I do it and it works out great for me and you use less bac water. Hope this helps bro if you have any questions you can add me and I can try to help further.

east coasts idea via tread is a good one.I would go with 5ml of bac water.That way 25iu's on a slin pin will be 250iu's of hcg.

THIS WAS TOLD TO ME BY TREAD-M great idea...

The ideal thing would be to have a 10 ml bottle of bac water. You would draw out 1 ml to reconstitute the hcg vial and then draw the 1 ml of hcg out and reinject into the 10 ml bottle of bac water. You now can mark the bac bottle "hcg". This gives you 10 ml with 500 iu's of hcg per ml. If you don't have a 10 ml bac bottle then you have to use your sterile vial and reconstitute the hcg vial with 1 ml and draw it back out and put in your sterile vial. Then add 9 more ml to the sterile vial for a total of 10 and same result. If you want less water you can split the water to 5 ml total and have 500 iu's per half ml.