posted Mon, 11/20/2017 - 11:17
3845
Heating gear before injecting
ad
Ok so I read all the time about people heating up the gear before injecting, it seems anytime I've tried heating up the gear and not real hot just kind of under hot water for a minute just get it warm make the oil a little bit thinner and easier to inject I get borderline Tren cough I can feel it in my chest it's not out full on I'm going to die I cough but it feels like it's almost going to happen. And it's like this with any compound And this is the same if I go in my Delt glute or leg
Just curious if anybody else has this experience with heating up their gear
- Bookmark
- 0
- 0
Heating the Tren obviously makes it less viscous and more susceptible to leaking into the blood vessels when they get pierced whilst injecting, its nothing to worry about and i know that feeling your talking about its happened once or twice with me too
Other thing to note is heating water based gear is pointless (ppl forget), there's a benefit of a smoother injection when its oil based gear
I wrap my vials in a heating pad on med, hop in the shower and they are perfect when I get out
As a rule, people heat the injections in order to make the oil more fluid or to achieve dissolution of the precipitate (resulting from crystallization). A normal solution of soft and flowing oil that doesn't contain a precipitate to heat doesn't make sense.
You can reheat vials in many ways: in water bath, by a cigar lighter, in a microwave oven. To warm up ampules is most comfortable in a water bath, on a steam and only to dissolve the sediment (but this happens very rare).
When I used injectable dbol I always heated up the vial before I pinned it in my tri's. The oil was super smooth and I had zero pip!
But be careful, too hot destroys the compound! I always used hot water and heated the vial inside for 1-2 minutes.
Be careful that there is not too much water around the vial the stopper should stay dry!
Never nuke/ microwave your shit not good fir your health at all, running under water not recommended either.
Best draw it into your barrel and use a hair dryer or heater to gently warm the oil, once warmed change drawing pin over to the pin you jab with, the best way to avoid any contamination.
Water is quite risky, I remember cutting myself real bad at work years ago on a building site, I automatically rushed to a tap to rinse, the doctors said I'm lucky not to caused a nasty infection and that I would have been better using my own piss to rinse it as water has lots of microscopic bacteria etc.
I always heat my gear gently. Just a little above room temperature, if I don't I notice a difference when pinning through a 25g needle. I've used many different sources' gear with varied viscosity.
I'm a little surprised people don't heat up.
Try to inject slower and steadier to avoid tren cough? That stops it for me.
I used to but if you draw big, pin small, no need to heat
I pin high density, high viscosity straight from the fridge that way, 19g draw - 25g push, no issues or need to warm oils
You keep your gear in the fridge?
lol sometimes
As im running a small bit of gh at the mo i have my deca sitting with it rather than run from room to room (aka lazy)
Usually itd be in a droor somewhere room temp
Even at the lower temp 25g is fine
RustyhookerWritten many forums on warming. Too hot destroys the hormone. I wrap it in my rice bag after 60 seconds in microwave .
Heating is best for small pin size and blending. Read my pip forums
I have read your pip forums goodshit I was just curious if anyone else had the same reaction I did when heating it up I typically don't have issues with Pip unless I'm painting test prop or high milligram gear which I just don't do anymore
RustyhookerYessir. Nick a vein and the solvents/oils flow thru your blood rather than slow absorption. I cough at times on all the different oils. Usually followed with lil blood at inj site.
Breathing slowly seems to calm the cough response for me. It does suck though regardless.
I used to heat up my gear but found it no difference all all if I heated it or not . I'm sure heating gear makes a difference for some people but not for me.
I'm the same way i tried heating for awhile then went back to just room temp and didn't notice a difference so i just pin it at room temp now!!
And then my brother swears by it , always heats it , different strokes for different folks I guess haha
Yeah my cousin is the same way hahaha