Personally, I find it more convenient to mix HCG with 5 mL of bacwater (when we're talking about just 5000 IU of HCG). That way, 1 mL of the final solution contains 1000 IU, which makes the dosing easier to calculate. However, for that amount of liquid, you'll probably need a larger sterile vial, and not everyone is comfortable injecting that much volume.

I always mix in 4mL of bacteriostatic water into my empty vials with HCG. Each 20 units on an insulin syringe equals 250 IUs, and 80 units would end up blasting 1000 IUs while 40 units would be 500 IUs. I would try to spread the HCG over larger time frames than this though since all you're trying to do is preserve testicular atrophy and get a small test boost to go along with your anabolic steroid. That's just my opinion though.

This helped more then any other that I've read! Pics helped too! Thanks a lot!

1ml usually accompanies 5000iu but for me hcg is very painful so .5 dissolves all of the powder for me and is less painful for me.

HCG being very delicate,once reconstituted just swirl the vial DO NOT SHAKE. as mentioned below....

How To Reconstitute hCG (Step-by-step guide w/Pictures!)

hCG is a peptide which is bought in powdered form. In order to inject this compound, it must be reconstituted through the use of either sterile water or bacteriostatic water. Both are acceptable re-constitutional ingredients, however the use of sterile water will see the hCG degrade at a faster rate than bacteriostatic water.

Preface
Assuming your vial of hCG is vacuum sealed (as many are), when you reconstitutie the hCG, withdraw your sterile water/bacteriostatic water then firmly hold the plunger of the syringe as you insert it through the stopper of the hCG vial. Don't let it suck the water from your pin. Turn the vial at a slight angle and slowly drip water down the side of the vial being sure not to shoot water directly at the powder. Your hCG should melt, if it fizzes up you've possibly just damaged the hormone. Do not shake the hCG, instead lightly swirl it and store it in a fridge and use for upto 30-40 days

Ingredients
1 x hCG Vial
Sterile Water or Bacteriostatic Water
1 x 1ml 29g 1/2" Needle (Insulin Needle)
Alcohol Swabs

Dosages
Working out dosages for hCG is simple.

+) If you have 5,000IU hCG in the vial, and 20ml of sterile/bacteriostatic water, reconstituting this will create 250IU/ml.

+) If you have 5,000IU hCG in the vial, and 10ml of sterile/bacteriostatic water, reconstituting this will create 500IU/ml.

+) If you have 5,000IU hCG in the vial, and 5ml of sterile/bacteriostatic water, reconstituting this will create 1,000IU/ml.

+) If you have 5,000IU hCG in the vial, and 2ml of sterile/bacteriostatic water, reconstituting this will create 2,500IU/ml.

+) If you have 5,000IU hCG in the vial, and 1ml of sterile/bacteriostatic water, reconstituting this will create 5,000IU/ml.

Step 1
Take the cap off the hCG vial, so that it is ready to be swabbed by an alcohol pad.

Step 2
Prepare Insulin Needle (1 x 1ml 29g 1/2" Needle).

Step 3
Use an alcohol swab to wipe the top of the hCG vial.

Step 4
Prepare Sterile Water/Bacteriostatic (Sterile water in this case) ampoule and identify cracking point.

Step 5
Crack ampoule.

Step 6
Withdraw water from the sterile water ampoule.

Step 7
Inject sterile water into the hCG vial, slowly and ensure the water does not come in direct contact with the powder, instead inject so that the water falls onto the side of the vial and hits the glass before it comes into contact with the powder - hCG alongside all peptides are very sensitive compounds.

Be very careful that there is no vacuum from the difference in pressure with the atmosphere and the pressure within the vial. To combat this, inject the amount (ml) into the vial before withdrawing that same amount (ml).

Step 8
Now either store the hCG in the fridge ready for consumption or inject subcutaneously (a step-by-step guide will follow).

one cc then if you want 500 you would draw out 5ius . you need one 3cc pin. and small insulin syringe.also put water in very slowly in vial