transferring from amps to vials
So I got some gear I asked for vials but got the same product in amps cause he was out. I want it in vials cause I can dose things at let's say 1.5 ml eod or .5 ml ed. With amps if I pop it I have to use the whole thing at once making my dosage plan Alot harder. I bought 10 empty sterile vials with the flip off cap on it.
My question is how should I go about this. I was going to do 3 amps at once then use a new syringe and needle for the next 3... is it necessary to do this or am I over thinking the process. I want to be as sterile as humanly possible while doing this or would it be better to buy a 10 ml syringe and do it all at once? I've never done this before so I'm not sure how to do it other than what I saw in videos I've watched.
Thanks guys!
- Bookmark
- 0
- 0
IMO, just take 30 minutes and transfer all the amps into sterile vials. I dont see a need to filter the oil as you would be injecting directly into yourself anyway. Equalizing the air inside of the vial is not difficult as you add amps, just pump in, pull out as necessary....(Thats what she said)..sry, had to.
Amps were the shit back in the day as it indicated pharma grade. UGL's didnt do amps since it wasnt cost effective....times have changed, and IMO amps can be more of a hassle busting them open everyday. To each their own though, but it is nice to see rows of testo depots
They really are a fkn hassle, out of idk 20 of them ive crushed 3 of them in my hands trying to open them. Thank god I wrap them in a sock now so it doesnt slice my finger open. I learned that lesson a long time ago when i didnt wrap them in anything and one crushed in my hand and sliced my fingers open.
Why not use an ampule opener?
You can get them for around $8 and will always have a clean break with no worries of glass going into the amp.
I do this all the time. I have an empty sterile vial, i only use half an amp of sust eod and I put the rest in the empty vial, after i finish up a box of amps I use the vial until its done. Rinse and repeat.
I like this idea. Also note that with amps you get more than 1ml. Usually from amps you get 1.1 or 1.2 mils so you may not have room for 10 amps into 1 vial if done all at once.
Ya most of the time youre right, if you draw from the amp and it goes right up to the 1ml youre actually getting over 1ml, cause 1ml doesnt go up to the 1 on the syringe. I got these amps recently and they only went up to like .7 or so, im like wtf theyre all short, so i sucked it down to the 2 and it filled from the 1 right up to the 2, meaning it was actually 1 full ML, if im making any sense? Going up to that first 1 theres extra space in the bottom of the syringe etc, 1ml would only go up to like the .75 or so. This is why alot of us only get like 9 shots out of a 10ml vial when taking 1ml doses each time.
But ya ive been doing this all cycle long, I suck the whole amp up, and then push out some into the vial until it reaches the .5 on the syringe, which is actually like .7, when those 10 amps are done i move to the vial and finish that. And then do it again.
... you know I was wondering why all my vials were short an ml. I kept thinking I lost track of a pin along the way or something.
Do you think a .45 or a .22 filter would be necessary? I'd be going strait from the amp to vial?
I wouldn't monkey around with a filter. Just suck up the amp and put into vial.
You don't think a $4 filter after opening the amp to the air is worth it?
Why not pull 10 amps into a 10ml syringe and push it through a syringe filter into a sterile vial. It would literally cost $5 to do.
We are always injecting air into a vial before drawing so I don't it would make any difference.
This is what I was thinking
Cool I bought 5 empty sterile vials with the top already crimped on and I got a 10 ml syringe ad far as it not fitting I got 20 ml sterile vials I already thought of that
lol
I agree with Mitch, i think it's best to just make ready to pin syringes from the amps but if you decide to roll with transferring into vials the one thing you might want to keep in mind is that pressure inside of the vial. If there is air in there then you'll need to draw it out of the vial before you inject the oil into the vial, otherwise there will be too much pressure and you won't be able to get the juice in. Hope that's helpful
don't make it too complicated. Just prepare 2-3 syringes in advance. For example if you want to use 1.5 ml eod then pop 3 amps and make 2 syringes with 1.5ml each. I have been doing like this for years, never had a problem. Nothing is gonna happen if the oil stays in syringe for 1-2 days. Just make sure you put the needle on.
All my gear is made with ethyl oleate which I heard can melt the rubber plunger. Not sure I feel safe doing that
No bro ur thinking about guaicol that shit will melt not only the rubber but the whole syringe
i don't think you should inject into your body something what melts rubber plunger. If it can melt rubber then just imagine what it can do to your flesh. This is only my opinion. I'm curious what the experts have to say.
But then again, I'm always using the syringes plastic cheapest ones without rubber plunger. Maybe that's why I have never had any problems?
Get a 10cc syringe and pull up all the liquid from all the amps into the syringe using a Watson Needle Filter then transfer the whole amount to the vial. Repeat as needed. Obviously wash hands well. Wipe top of vial with alcohol wipe etc. Hope this helps.
I'm assuming you mean a micron filter?
Yeap!
Shit the Whatman is 130 dollars fuck that I'll use the whole ml lmao
He means a syringe filter. The brand doesn't matter. They are $3-4