posted Thu, 10/22/2015 - 14:34
2447
Slin Pin Question
ad
If i was shooting lets say 3 cc of gear EOD and wanted to pin with insulin needles is there any that are 3cc or would i have to pin 1cc at a time? could i screw the insulin tip on a 3cc syringe or no?
- Bookmark
- 0
- 0
I've done 3 cc every other other day (3rd day) and seriously, unless it's gear with the consistency of water why would you want to so often? I've used 21g, that stung, I've used 23,24,25g as well. 25g are so thin it's slow to get oil through them, and drawing using same needle takes ages, plus they bend if injecting from awkward angle which ends up causing more pip than a 23g. I guess what we really need to know (apart from if you're so low in bodyfat and about to compete and trying to leave no sign of injection!!?) Is why you would want to?
Jesus, just use a fkn 25G, I have ZERO problems pushing oil through one, I have to actually slow down or it goes all in less then 15 seconds. Then I get to watch it try and ooze back out. Thats with GSO mind you. Is it the pain of the needle that scares you? Or is it how you magically became 25 years old after you found this site? If you truly want to be like Bostin lloyd he uses 19G 3cc. And he also injects that into his delt. Try using high mg gear as well, 3cc of 500mg sus.
After reading through my being a dick you might be able to see why I say what I say.
Now why on earth would you want to pin 3cc in one go?
Maybe really low rip blend like 150mg/ml tren, test, mast? Although even that sounds dumb. If using slin pins for that 1.5ml ed would make more sense. Fuck, hate browsing through forums and seeing this kinda thing and its just confusing and difficult as want to make sense of it
He has his 3 cc hat from Boston Lloyd, so he's got to represent.
lol.
I could spend half hour typing my slin pin protocol , but i feel it would be a waste :/
Not a waste!
I for one, would be interested, and I'm sure there would be quite a few others who would want to read it, along with inputs from other Mods and seasoned members. Might even be a good one to sticky! The search for the perfect combo of gauge/length per type of gear and injection site is always changing and rather evasive. Although I feel parts of my protocols work just fine, I feel like there is always something I could change. Its always great to hear other peoples experiences that others might not have thought of or specifically thought to try!
I'm going to write up mine one of these days. There isn't a site I don't use. God damn chore.
I'd like to see how you roll TonyT
I've been "back filling" 29gauge Slin Syringes and also 30gauge 1inch (1mL Syringes)
I haven't used a 25gauge for inject in forever
Fuck that nipro makes a half inch 27 or 28 I can't remember exactly could be higher that screws onto a nipro 3 or 5 cc syringe. Fuck all that backfill shit. I pull from the vial with my 23 while the oil is warm and inject with the half inch and I've never had a problem, it all goes through just make sure its warm, makes no difference, doesn't take long at all.
RustyhookerLast cycle I ran those pins. Pulled and pinned mct with no problems. You can get the 27 x 1 luer locks too for switches. Makes it cake
Nipro is pretty close screws on and screws off just the needle.
I use EXEL 30gauge (screw-on) with a 1mL syringe (MCT flows good for me with this set-up)
29gauge 1/2inch slins (delts)
I "back fill" these. Any possible sanitary issues? I've been doing this for awhile. Figured it was similar to drawing up a stealth sachet
Short Esters (Test P/Tren A)
25gauge just isn't an option for me anymore
Sanitary ehh... I just think its less work to draw with a 23 while oil is warm screw off the 23 gauge needle , screw on the 27 gauge half inch and be done with it. Get it up to body temp and it all flows through fine never had a problem. I don't do anything else brother. Run all my sites , calves , quads , hams , chest , lats , traps , front side and rear delt , bis , tris and now added forearms into the mix. I imagine adding the step of back filling a slin pin could up the risk in the sanitary department just one more chance for something to fuck up I suppose.
Thats what i do
No need. It's like the 4th thing on the post.
https://www.eroids.com/forum/general/general-talk/viking-tribute
Spend the half hour typing it, what else are you gonna do, rock back and forth in your rocking chair? ;)
It's never a waste to those of us who truly appreciate the golden nuggets, you know that.
Lmao!..... cheeky young fuck!
I was young like you once........... see.. i even have proof .
https://www.eroids.com/pics/a-little-something-from-32yrs-ago
Fuck me... that was before you born............. lolollolol
I laughed good on that.
Holy shit... Was that cave painting my brother?
It's amazing that 32 years ago you looked better than most of the guys that do this shit today!! Wait till all the youngins on this board start trying out genetic modification and all of that ish that they come up with in the next 10 years and still can't hit that type of physique!
haha yeah............. and cloning maybe?
You plan on starting your own Viking army, are ya?
that would nice bro....... i would have somebody to talk to that understood wtf i was going on about lol
Because a lot of people always think more is better...lol
No point in pinning if you can't take them oil pipes
To use a slin pin you've got to be lean as compounds are for deep intramuscular injection and if your not going deep enough you have the risk of the oil laying where it shouldn't. ...
Man up and get the oil pipes out
Do you know how the search function works mate? Not having a go but you could easily find your answer using the search here or on this really awesome website called www.google.com. Ever heard of it? The answers you are looking for are a few clicks away. Good luck and I really hope you are at least 25!
Stats
Age: 25
Height: 6'0
Weight: 200
BF:
I wonder what the BF% is... I see that BF% is still the sweep it under the rug and hope they don't see stat...
You can use SLIN pins
1cc at a time. BUT inject real slow
The gauge would have to be big enough to push oil ,and it would have to be long enough to get to muscle ,other than that get what you need ,don't cut corners brother ,3ml 23 gauge 1.5 syrenge is golden ,prices are about 20 for box of 100,pm me if you need me to point you in the right direction
I only used slin pins for B12 which is water.
I think it was 29G, you won't get oil through that.
I was reading guys using 27G for delt shots but id say it's quite a push.
I highly doubt you could push oil through a slin pin bud. Just stick to 25G.
What are your real stats?