posted Mon, 03/04/2013 - 07:37
1950
+ 2 Pre loading syringes
ad
I was wanting to know if anyone pre loads syringes? I was thinking about sitting down one day a week and loading all my syringes to last me a week or 2. Anyone see any problems with this?
- Bookmark
- 2
- 0
Don't do it, the rubber will get eaten up and give you some nasty pip if not an infection.. Best to just play it safe and take the extra 5 mins a day to draw and heat up with a hair dryer
probably the best advice to follow.....that being said ive laid out full cycles in preloaded pins before, months worth and never had any kind of problems. but I had good reason to do it.
X2
100% agree
WithdrawlI preload my syringes for the week and keep them in a plastic bag. I hide this shit from my wife so I have to be strategic, lol. I've done this in the past as well. Never had a problem. That doesn't make it ok though. This is just my personal experience. I also have only done this for test, deca, and eq. All were at 200mg/ml except for EQ recently that was 300mg/ml. Basically, nothing I've preloaded had any kinds of super solvents in them. They were all basic BA/BB stuff. If it's high mg gear I'd worry about it eating away at the plunger.
BostonOm in the same boat! Gotta hide the shit from my woman. I guess ill just have to wait to pin after she goes to bed lol. Hopefully she doesnt wake up screaming WHAT THE FUCK ARE YOU DOING!!!??
I like to prepare everything just before pinning to avoid mishandling.In my case Juice is better kept at my office (locked), since my wife and kids are always checking around the house. Last time had a discussion about some Clomid/Nolva she found at my night table. I was like "HuH Huh that is to lower my high libido, you are always complaining about me being horny all the time"
What about the days you are stacking them with several oils. How would you know which is which?
BostonPinning 3 compounds in the same syringe mon wed fri. Not an issue
I have done that 2 times! Both times with MISERABLE results in the form of a quarter size ball in my glute that after extreme pain turns into a hard patch of muscle and eventually goes away. Yes it took me 2 times to figure it out.... LOL The last time I loaded went and took a nap so an hour latter it did that to me.. LOL Wish I had thought to ask the question you just asked before I did it... ;) +1
BostonI thought that could happen! I am very glad i asked and i will be taking your advice my man.
Wardi77I have read somewhere that EO in the the gear apparently eats away rubber, for example the rubber stopper on top of the vial. Whether its true or not, I do not know and have not found any conclusive evidence to support it. Seeing as there is a rubber tip in the plunger of syringes I would be a little cautious preloading, but since it would be injected within a week then I think it should be ok. If anyone else has any information on this matter, chime in. I am interested to see whether it is a myth or not, I guess there would be no problem at all if your gear did not contain EO.
BostonHaha...funny because the gear ill be using soon is geneza and they use EO. Thanks for the replies guys
I've done it for up to a week with EO. I haven't had an issue, but it looks like others have. I tolerate it completely fine- nothing any different than drawing right before. EO will dissolve things quickly though. One of my pins leaked and it dissolves the black measure markers on the syringe... Made me think twice about leering it sit for too long
BostonDamn if the shit can dissolve rubber than why the hell are we shooting this stuff in our asses???
Hahahaha Really
i wouldnt do them that far ahead depending on the solvents used they can start to disinagrate the rubber plunger i see no problem doing a couple days in advance but i would not do more than that