Mixing 2 oils in one syringe, whats your technique
I just pinned my first pin of my 2nd cycle. I will be doing a 16 week cycle. kick start with 100mg prop,EOD mixed with 300mg test e x2 week. I never relized how tricky it would be to mix the two oils in one syringe.
here is what I tried to do would like feed back to see of there are better ways:
First I pulled slightly more then 2 ml of air into syringe. Then i pinned into the prop vial and shot 1 ml of air in to that vial. then slowly pulled 1 ml of oil out. found it diffucult to measure with out having oil leak out. then i pinned into the 2nd vial (test e) and pushed the rest of the air into this vial. i noticed it looked like some oil went into this vial as well. after pushing in and out gently a couple times I finaly managed to get 2 ml total of oil. I'm a little concerned with the mixing of the 2 oils into the 2nd vial. seems like after a while the dilution process would throw of the accuracy of knowing how much test e compared to how much prop is actually in the syringe? also seems like a lose just a little oil during this process, but over the length of the 16 week cycle that will add up to a significant amount. does every one experience this issue? or ais it just my inexperience?
Always enjoy the responses I get here on eroids, and am looking forward to it this time as usual?
- Bookmark
- 0
- 0
dont leave air in the pin when you get ready to pull in oil, push it all into vial then pull.
draw air into syringe, draw a CC, draw more air in, inject only air into other vial, and then draw from that vial. Quick and painless.
My bad it would be from the 3 to the 1, just saw my own typo
appreciate the response, however it seems to me your math might be off, if I fill from 3 to 1 that would give me 2ml of test e 300mg which would be 600mg plus 1ml of 100mg of prop to total 3 ml. I am only doing test e @ 300mg x2 a week for a total of 600mg per week and 100mg of prop. so that would be a ml of each when doing the both on the same day and just a ml of prop EOD. I understand the pinning schedule and amounts just dont have experience with mixing oils in same syringe.
You are way over thinking, draw a cc out of each vial is exactly how it sounds, draw a cc from each vial and as simple as it sounds. done
Hahaha, yea well that would be about right. I tend to over think most things it's a side effect of my daily work.
well in all fairness in this game its way better to overthink then to under think.
Using a 3ml set up pull your E into the syringe first, then hold it with the needle pointed to the sky measure from the bottom up. You would still have 2ml juice just from the 3 then to the 2. That leaves 1ml left in the syringe, put in your prop and fill that joker up and happy pinning.
RustyhookerPoint needle towards sky and second bottle won't spill over. Bubble goes to top. No need to get every drop of air into second bottle. Get the bubble up to pin and draw.
Takes practice. ...
thanks rusty, so do you pull air in the syringe to the total of your intended dose for both oils and inject to the vial first for negative pressure effect or no?
RustyhookerYes.
Examply...2 cc oil needed. 2cc air...1cc into first tgen draw. Repeat on 2nd etc. If pin side is up the bubble will be at pin side. Easy to read 1 cc too.
Ok cool, pretty much how I did it, just need some practice is all.
Ok cool, pretty much how I did it, just need some practice is all.
rxagentDraw out how much I need from the first vial, second, third, possibly fourth, and unlikely but maybe also the fifth (kidding).
That's pretty much it I don't inject air into the vials before drawing. If there is too much negative pressure it's a two second fix down the line when and if it's even needed.
No need to over complicate it