P's picture
P
  • 0
  • gADM
  • CC
default
12461

Step-by-step Injection Guide: Pecs (Intermediate Injection Sites)

ad
Default - Use Group's defaults.

Introduction

Injections can be stressful for some; so to ensure this process is as easy as possible I have created a step-by-step guide on how to inject. This is a complete guide which includes the aids you will need to have pre-injection, during your injection and post-injection, while also recommending methods to prevent PIP (post-injection-pain).

Here's my injection guide' roster;

+) Introduction
+) Pre-Injection Aids
+) Intra-Injection Aids
+) Injection Preparation
+) Injection Procedure
+) Post Injection Aids
+) Conclusion & Recommendations

Pre-Injection Aids

~ Vial or Vials of AAS compound(s)
~ Syringe 3ml
~ Drawing Needle/Pin 21g
~ Injection Needle 27g/29g/Insulin Pin (are all acceptable)
~ Alcohol Wipes
~ Sharps Container

Intra-Injection Aids

~ Warm water
~ Towel
~ Bowl

Injection Preparation

As I do with all of my injections, my first step is to always warm up the vials of AAS I will be using. To do this, I first ran the hot water tap until the heat is above room temperature and proceed to fill up a bowl with the hot water to approximately 3 centimeters in depth. The AAS vial will then placed in this bowl for 10 minutes.

Once the vials have warmed up, I then dry them with a towel (and flip of the cap if the vial is new/unused). Next, take an alcohol wipe (1 for each vial) and wipe the tops to remove and bacteria or any other dirt which can cause an infection. Then, remove the syringe and the 21g needle from their packaging and attach together (some screw together, others need to be pushed together). Then inject the amount of air into the syringe to equal the amount of liquid you will be withdrawing from the vial to make sure the pressure within the vial is safe (if you are drawing out 1ml of AAS from the vial, then inject 1ml into the vial - this will also make drawing the liquid AAS compound a lot easier). Place the cap on the 21g needle and un-package the 29g and attach to the syringe.

I then select the site I am going to inject. This is my right side quad and begin to follow the injection procedure outlined below.

Injection Procedure

The image below shows the places on your pec where you can inject, select a site and follow the step-by-step guide below;

1 - Remove any lengthy pieces of clothing from your torso, so that your upper chest and torso is free.
2 - Bookmark a space three finger widths vertically above your nipple and two finger widths horizontally towards your inner chest.
3 - Bookmark this site for injection.
4 - Wipe this area with an alcohol wipe.
5 - Sit down.
6 - Flick the syringe with the AAS compound in to remove any air bubbles and push the plunger so that 1 or 2 drops come out to lubricate the needle.
7 - Push the needle into the alcohol swapped site.
8 - Aspirate (enough to see an air bubble / if you see blood, withdraw the needle, change the needle and select another pinning location).
9 - Once you have seen an air bubble from aspirating, you're ready.
10 - Push slowly down on the plunger to inject the liquid.
11 - Once all injected liquid has been injected, withdraw the needle slowly.
12 - Cap the needle and dispose of safely in a sharps container.

Post-Injection Aids

Shower - Once you have injected, take a shower and massage the area to disperse the liquid for faster absorbtion and minimal PIP.
Heat Pad - Apply a heat pad to disperse the liquid.

Conclusion & Recommendations

Always follow the safety precautions with every single injection you do. Make sure all your apparatus is disinfected and sterile and take your time when you inject.

Any comments, queries or issues on the topic of injecting can be discussed below

Trenabolic's picture

I like it p, pecs are a great place to pin.

levelup's picture

pec is one of my favorite spots to hit. i use 25g 1" and up to 2ml...from the looks of everyone elses pin choice mine might be a bit large. can anyone comment on that?

snuka2012's picture

25 g and 5/8 works for me...oils seems to pass through just fine...haven't gone beyond 2mL.

Catalyst's picture

Depends on the oil mate. I've used a 25g in the past as a particular oil would not go through a 29g and tbh I never get 27g personally. I tend to use slin pins (29g) for pecs and tris, but I didn't have any issues with a 25g the few times I used it.

j223's picture

27 works perfect for me

Catalyst's picture

Think I'll pick up a few then next time I'm pin shopping.

P's picture

You get yours from the exchange?

Catalyst's picture

Yep, I use the local needle exchange / drug counselling service. Has a steroid clinic too so I get blood tests whenever I want as I've done some talks for them because of my job background etc. Get some very strange looks when you're standing next to three crack heads that probably weigh the same as I do put together lol!

P's picture

LMAO, me too brother. The feeling when your in a queue and there's a crack head in front and 2 heroin addicts behind, plus mine is in a dodgy alley! Hahaha, adds to the experience.

Catalyst's picture

Same here, a dodgy back alley filled with drunks etc.

All adds up to a "character building" experience.

levelup's picture

thx! ive been used 29g 1/2" for tris but every once in a while a little oil slips out sub q and irritates the hell out of my arm. ill give it a whirl on the slin pin for the pecs

j223's picture

Thanks for the post! I just injected pecs 0.5cc tren ace in each and zero pip! I like this spot and I'm going to include it into my rotation now

P's picture

I love this spot too! What size pin did you use?

j223's picture

I used a 27G 1/2 inch. I drew it with a 23G then put the 27G on.

edit: It was either a 1/2 inch or 5/8ths I don't remember but I have very little fat there

humpnpump's picture

How many cc's is typical for chest, will it hold 2 cc's well. Thats were I pin my TNE 1/2 to 1 cc and never had a bit of pip. I really like this site and its easy to pin. I'm just curious how much is typical for future refference.

Catalyst's picture

I've put 2ml into a pec without issue. Not sure would be the case for everyone mind you.

P's picture

I personally don't go above 1.5ml for pecs and depending on the person and amount of pectoral muscle mass they have 2ml is possible at a stretch.

What size needle do you pin pecs with?

humpnpump's picture

Sounds good. I use 29 g 1/2" slin pin works great.

Anonymous's picture

Good stuff