posted Thu, 08/14/2014 - 01:53
3210
test suspension?
ad
Im excited to start hittin this suspension pre work out. Im gonna draw with a 18g and attempt to use a 23g 1.5" in glute. Any techniques for pinning suspension or getting the oil in you without clogging then shit outta the needle?
- Bookmark
- 0
- 0
I used an 18,it's like using a fucking nailgun in the quads. TNE became my friend shortly after that, I through the Aqua away...Maybe it was poor quality, I'm not sure, I heated it too. Not worth the aggrivation for me personally. There are other compounds that can get me there
Oil Test Suspension in my opinion, after a 8 week cycle of 200mg EOD, was VERY painful and left awful lumps like Ive never had before. Dont get me wrong, the gains were excellent, the fat loss was excellent, the strength was top and my libido was out of control.... so were the side effects mind!
I drew up with an 18G Pink, and shot with a Blue 23G 1.5" in glutes.
How to stop the clogging and floaters? Heat the vial or amp in some "off the boil" water for a few minutes, then give it a good shake and put it back in again for another minute or so. Then draw up ASAP and fire away. This in my opinion helped.
I've only ever bought test suspension from top sources so that may be why I have had very little problem pinning even with a 29 ga slin pin.
I shake, quickly draw with a 20 gage, back load the slin pin and let er rip before it can settle. I prep the injection site with alcohol before loading so I'm ready to go as soon as it's loaded.
Maybe lower quality product is lumper?
If I had to shoot it with a 21 or 22 gage I'd stop using it. If I had to use a 18 ga I never would have used it to begin with. Fuck that.
Idk why some does and some doesn't but I'll tell you mine is from one of the biggest labs in the world in my option the best gear I've ever used and it still clogs. It draws easily I could probably do it through a 23 but I use a 21 for both and it always cloggs
Have you tried heating it or shaking it?
Some say that helps with the water based Test Susp?
Just pin it with the same 18 gauge that you drew it with. If you are going to pin with a 23 gauge you will probably have to work the plunger back and forth as you pin it.
I love h2o test suspension
Ever pin it 4x a day?
Lol, no. Twice was as tough as I wanted to be.
Lol twice a week is about all I can stand! Found the answer to my question tge other day it was in an old post where viking was talking about some old school bb cycles and how tgey used tne.
Same here bro... Learnt the hard way.. Test-Sp and pining quad is a bad idea LOL... I stick with the glutes
18 ga is a bitch to pin with, I would opt personally for the 22-23 ga 1.5" Glute pin.
Lol, my sister pins her suspension in the glutes with 22-23 gauge pins.
I like
I've got some TS I can draw and pin with a 29g slin pin. I get in a set position to pin, shake the vial draw up and straight in. I get pip in my quads but not in my glutes. I sometimes mix it with normal oil gear and pin with a 25g.
My advice to you, get tne instead. Water based suspension is a huge pain in the ass. Always clogs even through a 21g. I'm never buying it again, but it's a awesome preworkout.
^^^^---Agreed!
Draw an air bubble into the barrel, cap and shake it up. It'll hold suspension for a short time. Just pin before it settles.
What does that's do? Just stop it from clogging the pin?
Yes. Water only holds suspension for so long before it settles at the needle port. I've always used 23g and never had an issue. But since I've found tne, I've not looked back. Suspension seems to hit a lil hard for some reason. At least it seems that way.. But i still like tne better
I got some tne on the way from a domestic source and then I got in on a promo where the source was giving out coupons so I figured I'd grab some pharma grade compounds for my bulk and try a few amps of the aqua suspension.. see which one works better for me as a pwo. From what it sounds like tho tne is the route to take.
Water based ive used a 23g but ive also clogged up a 23g. I find that if I pin it as quick as I can after I draw it up that its less likely to clog. Also I dip my pin in some gso to lube it because I have had a pin come to a screeching halt half way in. Pip........ yes your gonna experience some pip! I prefer oil based myself and the brand I use is suspended in mtc oil, flows great through a 27g.
I heard water based is a pain in the ass but I used tne oil base and it worked fine with a 22 gauge 1 1/2 on quads..I got some aqua suspension on the way and a Buddy told me he had to use a 18 gauge to pin and pip sucked..guess I'll find out in a week or so.
Talk about leave a hole.. That's a piercing not a pinning. Lol
Yea man I couldn't imagine having to constantly pin with an 18 gauge..I use a 22 gauge 1 1/2 inch for my usual pinning..hopefully this aqua suspension that's in route doesn't involve a dagger of a needle.being the newb that I am I get my pins from a farm supply store and they don't have a huge selection of cattle syringes lol..I just need to stop being lazy and order some from a med supply company on here.
Is it in oil or water?
Water
They vary. Shake it up, you may need a 21g. I've got some in the stash that won't even go through a 21. Needs plumbing supplies to pin it I think!
Lol