Still new to this myself but the below is an online calculator for working it all out, just fill in the Blue numbers

http://peptidecalculator.com/calculator.php

How To Reconstitute GHRP-2 Peptide (Step-by-step guide w/Pictures!)

GHRP-2 is a peptide which is bought in powdered form. In order to inject this compound, it must be reconstituted through the use of either sterile water or bacteriostatic water. Both are acceptable re-constitutional ingredients, however the use of sterile water will see the GHRP-2 degrade at a faster rate than bacteriostatic water.

Preface:
Assuming your vial of GHRP-2 is vacuum sealed (as many are), when you reconstitutie the GHRP-2, withdraw your sterile water/bacteriostatic water then firmly hold the plunger of the syringe as you insert it through the stopper of the GHRP-2 vial. Don't let it suck the water from your pin. Turn the vial at a slight angle and slowly drip water down the side of the vial being sure not to shoot water directly at the powder. Your GHRP-2 should melt, if it fizzes up you've possibly just damaged the hormone. Do not shake the GHRP-2, instead lightly swirl it and store it in a fridge and use for upto 30-60 days

Ingredients:
1 x 5mg GHRP-2 Vial
Sterile Water or Bacteriostatic Water
1 x 1ml 29g 1/2" Needle (Insulin Needle)
Alcohol Swabs

Dosages:
Working out dosages for GHRP-2 is simple.

With 2ml of bacteriostatic water in the 5mg vial, here are what your doses will be;

+) 2ml of bacteriostatic water in 5mg of GHRP-2 = 100mcg/0.04ml (0.04ml = 2 ticks on an insulin pin).

Step 1:
Take the cap off the GHRP-2, so that it is ready to be swabbed by an alcohol pad.

Step 2:
Prepare Insulin Needle (1 x 1ml 29g 1/2" Needle).

Step 3:
Use an alcohol swab to wipe the top of the GHRP-2 vial.

Step 4:
Prepare Sterile Water/bacteriostatic.

Step 5:
Withdraw water from the bateriostatic water vial.

Step 6:
Inject bateriostatic water into the GHRP-2 vial, slowly and ensure the water does not come in direct contact with the powder, instead inject so that the water falls onto the side of the vial and hits the glass before it comes into contact with the powder - GHRP-2 alongside all peptides are very sensitive compounds.

Be very careful that there is no vacuum from the difference in pressure with the atmosphere and the pressure within the vial. To combat this, inject the amount (ml) into the vial before withdrawing that same amount (ml).

Step 7:
Now either store the GHRP-2 in the fridge ready for consumption or inject subcutaneously (a step-by-step guide will follow).

Ok 5MG/5000MCG...1ML/100IU...3.5ML/350IU...
5000MCG divided by 350IU= 14.3MCG/IU
100MCG divided by 14.3MCG= 7IU or 7 small tic marks on a 100IU syringe.
All math rounded up.....
Correct me if I'm wrong.

DO NOT use .7cc!!!! Not bashing but I believe the math is wrong. At work and busy will post ASAP formula and math to resolve this issue.

Mixing (reconstitution) the lyophilized product in their vials with Bacteriostatic Water (BW) can take some getting used to. The idea is not to add too much dilution. Typical rule of thumb is to add 0.5mL of BW to 1mg of Peptide. So a 2mg vial should reconstitute with 1mL BW. 5mg with 2.5mL, 10mg with 5mL, etc. Squirt the BW along the inside wall of the vial in a smooth controlled manner being cautious not to agitate the mixture too much. It will dissolve itself and become clear. You can roll the vial gently between your fingers or hands but don't shake it to dissolve. The reconstitute is ok to be drawn once fully dissolved.

On a 1mL needle, there are either 50 tick marks from 0-100, skipping every odd number OR 100 international units (IU). A 100mcg dose is half way between the 2nd and 3rd tick mark, OR 5 IU's (if you followed the above reconstitution). There are no half tick marks. It is OK to draw modGRF and GHRP into the one needle for a single shot. It is NOT OK to mix peptides in the same vial or syringe for storage.

either get some empty vials and put it in there with 5ml, or u can put 2.5ml and draw until about the third tick, you'll get a little more then 100mcg