posted Wed, 05/27/2015 - 04:04
3389
tip for injecting test suspension
ad
I love water based test suspension but I've always had hell with it clogging my pins when i try to inject. Ive used 22g and 23g and still have it clog. Now im sure i may catch some heat for what im about to suggest but I've been doing this successfully for two weeks now. I didnt have any injectable b12 so what i done i drew up half a cc of test e then a full cc of suspension followed by another half cc of test e. Ive have yet to clog a 23g using this method. Lots of people are against mixing oils with water based products but after several jabs and clogged pins i was desperate to try anything. Lets hear your thoughts and opinions .
- Bookmark
- 0
- 0
Tried this technique this morning and it worked like a charm, no clog using 22ga 1 1/2 inch? But after this round i think ima run with tne since its same thing but oil based
I'm gonna swap brands and give it another try but i prefer tne. Love the smell of that stuff!
I haven't tried it but fuck man after this gnarly ass pip I want to lol I mean I feel it like almost instantly but then its almost not worth it cause I could barely get a good wrk out
thank god ! i started to think i was the only one ! i always kinda thought maybe mix it but knew the whole oil and water based was taboo
Handsumhustlaa23I usually fill it in syringe and run the syringe under warm/ slightly hot water and pin right away. 22G. But to be honest you may have gotten bad suspension bc the first time I got water base it was smooth and went right in no prob.
MightyMatt812I never had a problem I use 25 gauge shake vial up very good pull and pin right away I always use delts when pinning it I barely use any pressure and flows right in
Well I've obviously got some shit suspension. To bad i cant tell the brand in here ha!
MightyMatt812That's what it sound like if it's good raws it will flow good
I've used your approach and it worked well for me. Through a 25 ga. Seemed like it lubricated the inside of the pin a little. I didn't split the dose like you did I drew up the oil then I drew up the suspension. The suspension just floats around in the pin anyways. I didn't want to risk getting any contaminates inside of my vial of test.
I've also just pinned it and if it clogs I pull the plunger back and retry until I got it all out. The amount of pip is dictated by how many times you clog the pin. Lol. It is suspension after all its gonna hurt
Man this stuff is so bad i cant even draw back on the pin and unclog it! Ive pulled the pin out swapped it with another one and clog it too! But yes its like it lubricated it amd keeps it from clogging. Also the suspension is trapped in a bubble instead of settling to the bottom of the syringe. The reason i drew test a second time was to clear the pin of any suspension that might clog it. (In theory)
I've only tried test suspension in water from one source on here but ran into the same issue. It was very frustrating but when I mixed it with 1 cc of test prop it flowed through no problem. Like you, I read a good bit of post advising against using this method but I didn't run into any problems.
oil bas and water base mix g2g then ? i mean its not traditional but make sense
I agree with the quality issue because I've seen you mention before that you've used a 27g. I just recently ordered 2 different brands that i haven't tried yet, maybe they will be better than what i have now.
Change sources, i used a 27g slin pin when I was using suspension, no clogging, straight in!
As for mixing oil n water based suspension, ive done this as well, not to help it pass through but to reduce pip. Pip free when mixed with oil.
The particles of the Test raw powder should be micronized in the suspension. Ultra micronized suspension can pass through a 25 gauge needle without clogging. Comes down to quality bro. This is far and away a pure quality issue. But, I liked the work around u suggest for mediocre suspension.
Absolutely. Most of the test suspension I have purchased from eroids sources is frankly crap. Also why it hurts usually.
Any of you guys ever used it multiple times per day ? Not only as a preworkout but before meals?
I've never associated it with a before meal thing, but I have run it as a base. To do that you gotta stay real focused on sterile procedure bro cause there is A LOT of pinning. I've done it a couple of times in my life. It's really the best base there is but too much pinning even for me. See what Flash says below.
a bit out of my comfort zone, he will do short high intensity cycles ( shic) about 3 times a year, he will use suspension as the base, pinning it 3 times daily, he will usually run that with tren ace which he will pin twice daily, plus oral halo , usually just a 4- 6 week blast, no way could i handle that.
Thats exactly what I've been looking into. It would probably be a little less painful with tne instead of suspension.
my mate pins it every 8 hours, half life is key 12 hours