posted Wed, 01/29/2025 - 20:42
1240
Heating Up Oils
ad
How do you guys heat up your oils ? I have always used a heating pad or candle warmer anywhere from 5-10 minutes
Stove Top with Pan
Candle Warmer
Heating Pad
Run Syringe under hot water
Vial in hot water
Bean Bags
Interested to see if you guys have anymore tips or suggestions
- Bookmark
- 0
- 0
ScarecrowGlass top stove. Just place the vial on the burner.
In a spoon with a torch.
Nah... I'll leave it in a cup of hot water or something for a minute or two.
Havent needed to in a while. DHB ill find/use any trick possible to negate the pip.
I heat my corn bags up then put my vial in between two of them. Out of shower then good it go
I like too pin in the shower run the hot water on the area I'm pinning
I just go raw daddy. Ice cold room temp from my top drawer into my muscle. Arnold said "if you use a heating pad make sure it matches your purse".... Nope jk sorry, he said "gloves" lol
I just ordered those schieck gloves there great
place a prefilled syringe (with draw needle capped) in a glass of hot water and take a shower. Swap out needle, pin.
Do you submerged the whole prefilled syringe @Greg
He’s trolling you.
Greg has been heating his oils Rectally for the past decade, and it’s been well documented as the most effective method.
Just the barrel and capped draw needle. Not t&e top of the barrel and plunger.
Thank you
I only heat my gear if it’s crashed and then I use my wife’s candle warmer. It’s pretty perfect, just put the vial on it and turn it on. I learned the hard way that you should put a needle in the stopper to let it vent though. I used to blast it ob the highest heat but now I set it to medium and swirl the oil every ten or fifteen minutes until it uncrashes. I think it’s better for the oil this way.
Be careful with that it will melt the plastic holding the needle and potentially contaminate the gear
? The rubber stopper acts as an insulator to the needle the stopper would have to melt first ..anyway been uncrashing gear this way as since 2005 never ever had a needles plastic melt --
That’s part of the reason I do it on medium instead or high now lol. I kinda think candle warmer is the riskiest way to do it but it’s so damn convenient. On the other hand, my buddy pops it in the microwave for 30 seconds and has never had an issue which seems insane to me so maybe there are worse methods
Better off sticking it in a frying pan on top of the stove and heating it up breaking bad style lol
Either wrapped in a small heating pad or running the vial under warm water for a few minutes. If it's just my daily trt micro dose i will turn the water on pretty warm, but not scalding hot, and leave the test vial in the water stream while i shower. If i'm cycling and doing anything more than a tiny bit of test i will do in a slip pin i draw everything up into my needle then wrap the needle in a heating pad and turn it on medium while i shower.
Either works just fine.
Run water through my k cup and have oil in zip lock bag. Let set 8-10 minutes seems to work for me. First cycle I never warmed the oil just used bigger gauge but I'm learning lol.
I was desperate the other day and used the heating in my car to get the job done. Took 5-10 minutes or so on max heat, and nearly burned my fingers off but it pretty much uncrashed my gear.
Oldschool heating pad “she gets pretty hot can even uncrash gear”…….so I go ahead and load up my darts roll the darts up like a doobie in a paper towel the put the darts into heating pad roll up the pad and stash it upright behind pillows in the bed…works beautifully of course out the barrel to the lip before injecting to make sure not too hot and if it is wait a minute before injecting
Never used a candle warmer, if I had that's what I would use to heat up oils prior to injecting. I usually put on radiator for 10 mins to heat up. Finds it tins the oil and flows easier when injecting.
Only time I've used a hairdryer is for crashed gear to put it back into suspension. Worked a treat everytime.
I’ve been using a hair dryer. If it’s late I’ll run it under hot water. I don’t heat up to inject tho. Only to draw and have shit ready for the following 3 days. Dont really get pip and like to take my time so haven’t had the need to heat up to inject.