posted Mon, 03/18/2019 - 23:26
1454512
USROIDS.COM
Estimated T/A:
We are USA domestic supplier only, due to a large volume of orders we are receiving, orders may take up to one week to receive
Minimum Order:
$200
Payment Methods:
we accept bitcoin (BTC) only ,no other payments
Please note
Considering you were one of hundreds of orders within minutes and you got a quality product in a timely fashion.. I'd say not getting stickers is an extremely minor thing to complain about
Not complaining one bit....was trying to distinguish between the 100 and 400
Hi, Before I start, I just want to clarify that this isn't meant to come off as a negative question/statement but a genuine question. I've been reading this thread and have noticed a few people complain about floaters/specs etc inside the vial and also a couple mentioning PIP with products that shouldn't really cause PIP or at least a very minimal amount. I'm not saying that it's a super frequent occurrence, but it's happened enough times for me to notice.
Now onto my question. This can be answered by Keys or customers. If products have floaters or specs, can I assume products would be sent out to that customer too or given some kind of compensation? Or if multiple people were to come out and say a batch of a specific product is causing PIP or a bad site reaction, would those people with that "bad" batch be sent out new products as well? I hope this doesn't come across as an ignorant expectation, but I'm currently in search of a source that I can put my trust in, and honestly would like for it to be this one since I truly like everything about this source other than the few instances I mentioned above.
Sounds like and from the picture posted it's just crashing, that's harmless, just the hormone powder separating from the oil. If it is that, and you put the jar in hot water from ur sink, don't boil it. It should dissolve in less than 10 minutes.
Crashing in 70 degree weather?
Cold weather isn't the only reason, could be just be a little too much powder. I've only dealt w this 10 or so times, the hot water has always worked and the gear was always great. If that doesn't work I don't know what's up
What about the stuff at the tops of the vials?
Hopefully just solvent condensation. Hot weather can cause that bc the solvents have a much lower boiling point than the oil. Hot weather can cause this. Just shaking the bottle should mix it all back together if that is thecase.
You would feel comfortable using this after filtering? I'd hate to be out 300+ bucks but I don't want to die pinning this either
I don't even have a filter, like I said in an earlier comment the hot water always worked in the past, so I'm hoping the same happens here if mine has floaters once it comes. If it does not work, i don't know man. This is my first order from this source
Ya I've never had to filter anything I've bought off of eroids before
Now that you said that I just checked my test and sure enough it has a a floater in it
Well maybe he can address us all in here then
I had a good size order a week or so ago, put all of it away and now I think I need to pull it out and give it a check
My order came in June I believe, you might be included in this issue so I'd check before you crack open
Website is up and running again!
Did the emails change? I got an email after I placed an order just now, immediately after. It looks different than the previous emails and Proton flagged it. Just curious. Anyone place an order today and get the same thing? I clicked on the link from the Telegram page and it’s in my order history. Probably just being paranoid…
[email protected] i use this only,otherwise it comes from a scam site
All is good. Just being cautious. Just got it paid!
I'm pretty concerned with these vials, not as bad as the horse cum we've seen but they have floaters in them. Also what looks like condensation on the inside? I have 16 of these test prop and had to spend 100 bucks on filters and sterile vials. They've all been stored inside my closet in a case
I checked the photos better on telegram, they are just TP crystals stuck to the glass
I’ve warmed these unopened vials before, floaters still on bottom
Not sure about Test prop specifically because the black cap ones I have from key look fine but I have had gear that no matter how hot I got it and mixed it up there was some crystallization (it can take a couple tries). I pinned the whole vial with no issues, what's the vials in your pic?
I’ve tried to warm these numerous times, it’s the test c250 white tops.
Definitely odd, seeing quite a few people posting more issues. I'll be double checking the 10 or so I'm sitting on. Key definitely needs to be address the issues people are reporting.
Some "high" quality gear there.
Hey man I have no problem admitting I was wrong this shit sucks!
Oh I'm not calling you out buddy at all. Just this piece of shit source.
This is not a new issue with this clown.
@keytech is just gonna eventually hop on and start talking shit, play the blame game, probably try to switch subjects etc etc.
Nothing will change.
My bad bro, I deserve it though I've been defending this on here.
Definitely sucks you're going thru this.
Worst part is key doesn't have a clue or any say in what product he's selling. It's all prepackaged, relabeled bullshit. It's all straight from chinahhh @Jockstrap CHINAHHHHHH